Executive Programs

Workshops

Projects

Blogs

Careers

Placements

Student Reviews

For Business

Academic Training

Informative Articles

Find Jobs

We are Hiring!

All Courses

Choose a category

Mechanical

Electrical

Civil

Computer Science

Electronics

Offline Program

All Courses

CHOOSE A CATEGORY

Mechanical

Electrical

Civil

Computer Science

Electronics

Offline Program

Top Job Leading Courses

Automotive

CFD

FEA

Design

MBD

Med Tech

Courses by Software

Design

Solver

Automation

Vehicle Dynamics

CFD Solver

Preprocessor

Courses by Semester

First Year

Second Year

Third Year

Fourth Year

Courses by Domain

Automotive

CFD

Design

FEA

Tool-focused Courses

Design

Solver

Automation

Preprocessor

CFD Solver

Vehicle Dynamics

Machine learning

Machine Learning and AI

POPULAR COURSES

Post Graduate Program in Hybrid Electric Vehicle Design and Analysis

Post Graduate Program in Computational Fluid Dynamics

Post Graduate Program in CAD

Post Graduate Program in CAE

Post Graduate Program in Manufacturing Design

Post Graduate Program in Computational Design and Pre-processing

Post Graduate Program in Complete Passenger Car Design & Product Development

Executive Programs

Workshops

For Business

Success Stories

Placements

Student Reviews

Projects

Blogs

Academic Training

Find Jobs

Informative Articles

We're Hiring!

+91 9342691281 Log in

Creating a Floor plan, Footing detail and Isometric view using AutoCad

Cross section of load bearing wall over spread footing.Aim: To draw cross section of wall over footing.Commands used:Line.Rectangle.Trim. Procedure:Step:1 - Create rectangle by typing "REC" in command box Specify the first corner point as (5,5)Specify the length of rectangle =0.9 units in command boxSpecify width of…

Md Sameer
updated on 08 Sep 2022

Cross section of load bearing wall over spread footing.

Aim: To draw cross section of wall over footing.

Commands used:

Line.
Rectangle.
Trim.
Procedure:

Step:1 - Create rectangle by typing "REC" in command box

Specify the first corner point as (5,5)
Specify the length of rectangle =0.9 units in command box
Specify width of rectangle =0.25 units in command box

Step:2- Create another rectangle -"REC" in command box.

Specify the first corner point which is 0.2 units from the starting point of first rectangle.
Enter the length of rectangle as 0.5 units the width of rectangle as 0.4 units.

Step:3 - Create the third rectangle command- "REC"

Specify the first corner point which is 0.05 units from the starting point of second rectangle.
Enter the length of rectangle as 0.4 units the width of rectangle as 0.4 units.

Step :4 - Line is drawn from the corner of third rectangle, command "L"

Give the length as 1.15 units
Move cursor downwards and give value 0.15 units and right and give length as 1.15 units.

Step:5 - Fourth rectangle is drawn, command -"REC"

Specify the first corner point at a distance of 0.05 from the third rectangle
Give the length as 0.3 and width as 0.6.

Step:6 - from the line drawn in step 4, at a distance of 0.3, draw another line with the distance of 0.15 units vertically and 0.3 units horizontally.

Continue it two more times, until 3 steps are created.

Step:7 -Draw another rectangle above fourth rectangle, command -"REC".

Specify the corner point as the corner of the fourth rectangle
Click on dimension -give length as 0.3 units and width as 0.05 unit.

step:8 - Drawn the fifth rectangle command -"REC"

Specify the corner point as the corner of fourth rectangular
Click on dimension -give length as 0.3 units and with as 1 unit.
Erase the unwanted line by "trim"
Result:The cross section of load bearing wall over spread footing is drawn.

Cross section of an isolated footing

Aim- To draw c/s of an isolated footing.

Commands used:

Line.
Offset.
Trim.
Procedure:

Step1: - Draw a line with command "l" and give 1 units.

- give command "l" and give the relative coordinates as @ 0,0.15

- Give the next coordinate as @ 0.38,0.25.

- Next coordinate is given as @0,1.6

- Give @ 0.28,0

- Next coordinate @0, -1.6

-Next coordinate @0.38, -0.25

- Next @ 0, -0.15 or close.

Step:2 -Draw an offset with the command at a distance of 0.04 from the bottom line to up wards.

Give the command of "o" and select the object and give the offset distance as 0.04.
Do the same at the right and left bottom end.
Trim the unwanted lines.

Step:3 - Give offset from the top line with an offset distance of 0.2 units.

Give the command "o" an select the object-give the offset distance as 0.2 -select multiple option a 9 such lines
Trim the excess lines.

RESULT: C/S of isolated footing is drawn:

Line diagram of 2 bedroom building.

Aim : To draw line diagram of 2 bedroom building

Commands used:

Line.
Rectangle
Offset.
Trim
Procedure:

Step :1 - Creating bedroom room (8.2x3.6) by rectangle.

Step-2 Use the command "Explode" and select the rectangle.

Draw an off set using the command “O”
In the command line enter “O” and specify the distance of3.6 units from the left bottom end.
Draw an offset using the command “O” at a distance of4.2 units from the right bottom end.

Step-3 Extend the two line in the bottom and in the top.

Draw an off set at a distance of 0.3 between the two line to bottom side.
Repeat the same step and create two offsets.
Do the same process in the top.
Trim the unwanted lines.

Step -4

Using line command draw a line at a distance of 3.2 units from the left bottom end to up-wards 0.9 units.
Using line command draw a line at a distance of 3.2 units from the left top end to down-wards 1.8 units.

Result: The line diagram of 2-bedroom building is drawn:

Cross section of load bearing wall showing foundation details.

Aim: To draw the c/s of load bearing wall showing foundation details.

Commands used:

Line.
Rectangle.
Trim.
Procedure:

Step:1 - Create rectangle by typing "REC" in command box.

Specify the first corner point as (5,5).
Specify the length of rectangle =0.9 units in command box.
Specify width of rectangle =0.45 units in command box.

Step:2- Create another rectangle -"REC" in command box.

Specify the first corner point which is 0.15 units from the starting point of first rectangle.
Enter the length of rectangle as 0.6 units the width of rectangle as 0.4 units.

Step:3 - Create the third rectangle command- "REC"

Specify the first corner point which is 0.05 units from the starting point of second rectangle.
Enter the length of rectangle as 0.5 units the width of rectangle as 0.3 units.

Step:4 - Create the Fourth rectangle command- "REC"

Specify the first corner point which is 0.05 units from the starting point of second rectangle.
Enter the length of rectangle as 0.4 units the width of rectangle as 0.6 units.

Step:5 - Drawn the fifth rectangle command -"REC"

Specify the corner point as the corner of fourth rectangular
Click on dimension -give length as 0.3 units and with as 1 unit.
Erase the unwanted line by "trim".
RESULT: The c/s of load bearing wall foundation details is shown:

Isometric view of steps.

Aim: To draw the isometric view of steps.

Commands used:

Line.
Isometric plane.
Procedure:

To work with isometric view -command "ds" - snap off, grid off. Put isometric snap on .
Make sure that ortho mode is on .
Step :1 - From isometric drafting select iso-plane left.

Give command "l" and moving the cursor to -x direction(left) give 1unit .
Moving the cursor to+ y direction (top), give 0.15 units.
Moving the cursor to + x direction again give 1 unit and cursor to -y direction(downwards) give 0.15 unit.

Step:2 - Change the isometric drafting to iso-plane top

Move the cursor to back and give 0.3 units from the last drawn point.
Move the cursor to right direction and give 1 unit.
Move the cursor to front and give 0.3 unit.

Step:3 - Change the isometric drafting to iso-plane right

Copy the object drawn, ortho off .
Command "co" and specify the base point and place it to new point.
Repeat it until 4 steps are formed.

Step:4 - With iso-plane right join the two ends with ortho off.

Result: The steps are drawn in isometric view.

Isometric view of gable wall.

Aim: To draw the isometric view of gable wall.

Commands used:

Line.
Isometric plane.
Procedure:

To work with isometric view -command "ds" - snap off, grid off. put isometric snap on
Make sure that ortho mode is on
Step:1 - From isometric drafting select iso-plane left.

Give command "l" and moving the cursor to right give 1 unit
Pointing the cursor upwards give 3 units
Draw 0.3 units to left and 3 units downwards and 0.3 units to left.

Step:2 - Using isometric right, take line command and draw line upwards of 2.42 units from the starting point of step 1

Draw 1 unit towards the right and 2.42 units downwards.
Using isometric left again, using line command draw 0.3 units to left side and draw a line which intersects the top line.

Step 3 – Using iso-metric right with the line command draw 1.0 unit to right Side and 3.0 units upwards.

Step:4 - By using the line command draw a line from bottom left corner @1.5 units and extend line 4 units upwards i.e., total 3.25 units from bottom.

Step :5 - With ortho off, draw a line between the corner of left side and the projected line done in step 4

Draw it to the other side also till it meets the right corner.

Step:6 - Draw the vertical line with ortho on @0.3 and join the vertical line using line from left and right end same as in the step 5 remove unwanted lines by using erase.

Result: The isometric view of gable wall is drawn: