MBD SIMULATION ON THE IC ENGINE VALVE TRAIN

AIM     To compare the performances of three types of beams under a bending load and to choose the best one among the three types CASE1: RECTANGULAR BEAM                                            …

AIM        To write a program to simulate the transient behavior of the simple pendulum and create an animation on its motion ODE                The above equation is a second-order equation. It cannot be solved as it is so it should be split into two first-order…

AIM         To write a program to create a visualizer tool which will read the given data and required information is taken from the data file  PROGRAM : import matplotlib.pyplot as plt import math import numpy as np import sys #compatibility check try : file = open(\'engine_data.out\',\'r\')…

AIM        To write a program to perform curve fitting. CURVE FIT            Curve fitting is a process of constructing a curve or a mathematical function that has been best fit to the series of data points. By curve fitting, we can obtain the relationship between the observed…

AIM       To write code to solve the Otto cycle and make plots on its pressure and velocity and find the thermal efficiency of the Otto cycle  AIR STANDARD CYCLE                         The internal combustion engines are considered…

AIM        To write a program to simulate the forward kinematics of the 2R robotic arm and create an animation file on the plot 2R ROBOTIC ARM                  It consists of two links. The first link is connected to the base in an angle of theta1. And the…

AIM          To calculate the drag force against a cyclist and to plot drag force vs velocity and drag force vs drag coefficient DRAG FORCE         Drag force is the force of wind or air resistance which acts again the velocity of the object which seems to be a cycle or…

AIM      To model the essential parts of the IC engine valve train and run MBD simulation on that. VALVE IN IC ENGINE         Valves in the IC engine are used to open and close the inlet and exhaust ports of the engine. The valve is placed with the support of a valve stem, which…

AIM      To run the motion analysis of the planetary gear with a sun gear, a ring gear, a carrier, and 4 planet gears. PLANETARY GEAR                Planetary gear system consists of one or more planet gears revolving around the sun gear. The planet gears are mounted…

AIM      To create the cad models of the driver and driven wheel and set up the motion analysis for the internal Geneva mechanism. GENEVA MECHANISM       Geneva mechanism is a gear mechanism which converts the continuous rotary motion into intermittent rotary motion.      …

AIM     To write a program to optimize the stalagmite function and find the global maxima of the function GENETIC ALGORITHM                Genetic algorithm is a method used to solve both constrained and unconstrained optimization problems based on natural selection.…

AIM      To write a program to simulate the transient behavior of a simple pendulum and to create an animation video of it. ODE                The above equation is a second-order equation. It cannot be solved as it is so it should be split into two first-order…

CENTRIFUGAL PUMP:                              Centrifugal pump is a device which is used to convert rotational kinetic energy into hydrodynamic energy of the fluid. STEPS FOLLOWED: Create a 3d model of centrifugal pump for the following dimensions…

              Flowbench is a device which is used to test internal aerodynamic qualities of an engine. STEPS FOLLOWED: Create a cylinder of diameter 100 mm and a length of 150 mm Then create a inlet manifold using sweep command of dia 25 mm The inlet manifold is of solid type make a shell…

Model the flow over a NACA0017 air foil For angle of attacks 0,2,4,6,8,10 compare the lift and drag forces STEPS: Insert the airfoil database and create a airfoil and make it completely closed. Use rotate entities and first give the angle of attack as 0 degree. Extrude it to a length of 0.1 mm. Save the part and click…

Simulate the flow over a cylinder: To calculate the baseline case reynolds no Run baseline simulation and calcuate the reynolds no .Then increase the reynolds no by factor of 20%,40% and 100% then run the transient simulation.      STEPS: Create a circle of radius 30 mm and extrude it to a length of 500…

https://drive.google.com/file/d/1ym-qeOUpZXZVsf1noBddxtUQ5b_MtEiI/view?usp=sharing                              In this challenge,I have learnt  velocity  distribution  through the pipe and how to noramlise the velocity profiles. …